NAME: LAME’ Colour 255
TYPE: decorative finish.
USE: water-based interior decorations.
TECHNICAL DATA:
Specific weight: 1.020 + 30 gr/LT. at 20°C
Yield: 16 - 20 m2/LT. (it may vary according to the roughness, porosity and surface absorption and to the method of application )
35 - 40 m2/LT. for the smooth effect (it may vary accordingto the roughness, porosity and surface absorption and to the method of application )
Aesthetic effect: glossy
Colours: colours from the catalogue
DRYING TIME:
On the surface: 2-3 hour at 20°C
Overpainting: 6-8 hours at 20°C
Below the painting: 48 hours at 20°C
PREPARATION OF THE SURFACE: remove old non-adhering and peeling paint from the support and wash using water and a suitable soap product. Next, apply a suitable fixative or a coating of Primer 400 diluted 50% with waterAfter approximately 4 hours at 20°C, proceed with the application of Meteore 8 laying gradually the product using the application technique according to the final aesthetical effect chosen .
PREPARATION OF THE PRODUCT:
Dilution: ready to use.
PRODUCT APPLICATION:System: stainless steel trowel et plastic trowel
Coats: 2
APPLICATION CYCLE:
Spatula-Stroke Effect: After about 4 hours at 20°C smoothen with 220 / 260- grit sandpaper to remove any irregular clots and joints. Subsequently apply two different-coloured coats of LAME’. Between the first and second coat of LAME’, wait at least 2 hours at 20°C. LAME’ must also be applied with the PV 43 Trowel in all directions, leaving very little product on the surface.
Coverage: METEORE 8 roughly 1 litre for 4 - 5 m2; LAME’ roughly 1 litre for 16 - 20 m2 (one colour coat depending on the thickness of METEORE 8 applied).
Veined Effect (Vertical, Horizontal, Oblique):. After about 4 hours at 20°C smoothen with 220 / 260-grit sandpaper to remove clots and any irregular joints. Subsequently apply two different-coloured coats of LAME’. Between the first and second coat of LAME’, wait at least 2 hours at 20°C. LAME’ must also be applied with the PV 43 Trowel in the direction of the streaks, leaving very little product on the surface.
Coverage: roughly 1 litre for 16 - 20 m2 (one colour coat depending on the thickness of METEORE 8 applied).
Smooth Effect:. After 4 hours at roughly 20°C, smoothen the surface using 220 / 260-grit sandpaper to remove any irregular clots and joints then apply two different-coloured coats of LAME’. Between the first and second coat of LAME’, wait at least 2 hours at 20°C. LAME’ must also be applied with the PV 43 Trowel in all directions, leaving very little product on the surface.Coverage: roughly 1 litre for 35 - 40 m2 (one coat for each colour depending on the thickness of the underlying coat).
Burano effect: Wait 3 - 4 hours at 20 ° C for the Meteore 8 to become dry and proceed with the application of a coat of Lame 'with 5 - 10 cm spatulas (or to taste) always using the PV 43 stainless steel trowel and be careful not to leave empty spaces.
Yield: about LT. 1 for 16 - 20 m2 (one coat based on the thickness of Meteore 8 applied).
N.B.: for light shades ( Meteore 8 not tinted) it is suggested to apply LAME’ with Plastic Trowel PV91
Application temperature: superior to + 5°C and inferior to +30°C
Storage: make sure the can is tightly closed, even after use, at a temperature no lower than + 5°C and no higher than + 35°C.Stability: approximately 2 years in well sealed and never opened can.
NOTES: Mix carefully the product before use with a wooden stick or metallic one .Application temperature must be between +5°C and +30°C. Wash the tools soon after use with water and soap.